Weha Hook & Loop backed edge wheels are built and designed specifically for horizontal machines such as Comandulli machines, Montresor edge polishers as well as vertical polishing machines: Sasso Flying Flat, Park Industries FastBack, GMM Tower, Marmo 711, and other polishing machines.

Designed to accommodate between 5-9 heads, the Weha inline polishing combo system will create a fantastic polish on marble, granite, dark quartz, light quartz, quartzite, porcelain, ceramic, sintered stone, etc.

The Weha inline polishing wheels are hook & loop backed for quick replacement without the hassle of removing the snail lock holders.

The Step 0 is not needed under normal circumstances. Only use #0 if the edge is not flat or extremely rough and needs some stock removal before step 1.

How to use the Weha 6" Donkey Quartz Polishing Pads for Vertical and Horizontal Inline Machines:

This Weha combo system took several months of R & D and has been tested on 5 head vertical machines as well on up to 8 head horizontal machines.

The combination of the Weha 6" Inline 3 Step pads and Donkey pads is producing an excellent polish on all materials with all machines.

for 5 head machines:

Step 1,2,3, Donkey Pad 1000,2000 or 2000,3000 depending on the stone and how much gloss you need to match.

Typical quartz use 1,2,3, Donkey Pad 1000,2000

For greater texture use Step 1,2,3 Donkey pad 600,1000

For 6 or more head machines the sequence can be the same as the 5 head sequence. You may add the 3000 grit Donkey for the occasional very difficult granite.

Machine Specs:

Step 1: 3 Bar

Step 2-6: 2.5 Bar

Feedrate: 120-250cm (48"-100"+) per minute depending on machineand color of stone.

How to use the Weha Donkey Quartz Face Polishing Pads:

To remove a scratch out of a quartz surface:

Start with the Weha Trio 3 step pads using a the Weha Aluminum Rigid Back up Pador the Weha Thin Rigid back up pad. Use all 3 pads, fanning out each grit, using the typical technique used for surface polishing.

After Step 3 start with the Weha Donkey Pad 600 grit, then 1000 grit,then 2000 gritusing the same fanning pattern. 1200 RPM or less.

After 2000 grit, dry the surface and see if the finish is matched.

If not, continue to the 3000 grit.

Occasionally, depending on the Quartz stone, a 6000 gritmay be needed.

If using 7 step diamond polishing pads, bring up to 3000 grit, then start back with the Weha Donkey Pad 600 grit, then 1000 grit,then 2000 gritusing the same fanning pattern. 1200 RPM or less.

To remove etch marks out of marble:

Start with the 600g Donkey pad with low rpm, 1800 rpm or less, and work over the area in 30 second increments.

Depending on the marble and gloss, a 1000 grit and 2000 grit maybe necessary

To remove a scratch out of a granite surface:

Start with the Weha Trio 3 step pads using a the Weha Aluminum Rigid Back up Pador the Weha Thin Rigid back up pad. Use all 3 pads, fanning out each grit, using the typical technique used for surface polishing

After Step 3 start with the Weha Donkey Pad 600 grit, then 1000 grit,then 2000 gritusing the same fanning pattern. 1200 RPM or less.

After 1000 grit, dry the surface and see if the finish is matched. If necessary move to the 2,000 and check

If not, continue to the 3000 grit.

Occasionally, depending on the granite or Quartz stone, a 6000 gritmay be needed.

If using 7 step diamond polishing pads, bring up to 3000 grit, then start back with the Weha Donkey Pad 600 grit, then 1000 grit,then 2000 gritusing the same fanning pattern. 1200 RPM or less.

RPM: 1200 rpm or less. Preferred Rpm 800

Tip: For repairs inside the home, soak the Donkey surface polishing pads in water for at least 20 minutes to absorb water. this will provide enough water for surface repair inside the home